Q: I have a Challenger 9300. I want to add a keyless entry keypad and remote control. Which one do I need?
Q: The new AL-9000 Photo eyes I purchased are already wired. Is their any way for me to utilize the existing wiring with my Challenger 2115 opener?
Q: Garage door won't close from remote controls only closes when wall button is held down
Q: Limited Range of Remote Controls
| Q: I have a Challenger 9300. I want to add a keyless entry keypad and remote control. Which one do I need? A: Wayne Dalton Challenger garage door openers were originally equipped with varying types of radio receivers and remote controls. If you have a remote control for your garage door opener, look at the pictures of remote controls listed on this page to find one that looks very similar to yours. Click on the picture and look at the section on the product page called "Compatible with these Models" to determine compatibility with your Wayne Dalton Challenger garage door opener. If you cannot determine what type you have, we recommend that you install a new radio receiver/transmitter. The one we recommend is our Universal Remote Kit (this includes the new receiver and one remote control). It is quick and easy to install. You can add additional remote controls at any time and also a wireless keyless entry keypad if you desire. For further information on the Universal kit, please visit this web page - Universal Remote Control Kit |
| Q: The new AL-9000 Photo eyes I purchased are already wired. Is their any way for me to utilize the existing wiring with my Challenger 2115 opener? A: Yes, the AL-9000 sensors are the correct model for all Challenger and Wayne Dalton garage door openers (including the Wizard 2115), so it is the correct sensor for your door, and yes, you can use it with existing wiring.Black wire on sensors go to OBS, white wire goes to COM. You can run them in series or parallel. You can splice one sensor to the other or run each individually to powerhead as long as black goes to OBS and white goes to COM. |
| Q: Garage door won't close from remote controls only closes when wall button is held down A: Usually when the door cannot be closed by remote control and the wall button has to be held down to close it, it means there is something wrong with your infrared photo eyes (found down by the floor on both sides of your garage door opening). Either they are not "looking" at each other, or they are faulty. The first thing I would do is make sure they are looking at each other (someone may have accidentally knocked them out of alignment or a leaf or debris may be stuck to the front of one of them). If they still will not work, they are probably faulty and need replacement. |
| Q: Limited Range of Remote Controls A: Limited range of your remote controls could be related to radio frequency interference that comes from something in your home or in the surrounding environment. Certain electrical devices can radiate interference; this could be almost anything that is plugged into an electrical outlet. Please keep in mind that the device can be brand new, or can be an item that has been in use for quite a while. Also, the item may continue to function properly as far as you are able to tell. The only problem with the item may be that it has started to broadcast the interference, with no other symptoms noted. Some devices are more likely to generate interference than others. This includes TV cable, cable amplifiers, surge protectors, fluorescent lights, battery charging devices (power tools, golf carts, etc.), anything that utilizes a timer (sprinkler systems, lights, alarm systems, etc.), and a myriad of others. If the problem seems sporadic, we can safely assume that the device responsible for the interference is only being operated during those times. Again, please keep in mind that the age of the device does not determine if it is capable of broadcasting unwanted interference. Any electrical device can be the source of the problem. The first step is replacing the battery in your remote. If the range on your remote does not improve, remove the wall control wires from the overhead unit. If the range does not improve you will likely need to replace the remote control. After replacing the remote, or if you have other remotes programmed in to the opener, and the range problem still exists, please proceed to the Power Down test. Multiple garage doors: If you have two garage door units and one is working just fine, you will need to start by unplugging the good unit. This will help determine if the unit with no range starts to function properly. If the range comes back to the bad unit then you will need to replace the logic board on the unit that was unplugged as it is emitting an RF signal that is over powering the other garage door opener. If the range does not improve after the "good" unit has been unplugged, replace the batteries and try programming some additional remotes to determine if the existing remotes are the issue. If the extra remotes do not have any range then you would need to replace the receiver logic board in the "bad" unit. Power Down test: To isolate potential sources of interference, turn the circuit breaker off to the garage and plug the garage door opener into an extension cord from another room. If the range improves, then the interference is coming from a device in the garage. If no improvement is seen follow the same procedure, this time turning off the circuit breakers to your home, with the exception of the garage, and test the remote controls. If improvement is noted, turn the circuit breakers back on, one by one, until the range problem resurfaces. This will allow you to narrow down what room the problem device is in. You will have to go from there to isolate it further, by unplugging and re-plugging the items in that room. If you are unable to determine any source of interference, then the receiver logic board in the overhead unit will need to be replaced. |